home » Archivo de Tubos de plástico de soldadura

About Tubos de plástico de soldadura

This author has not yet filled in any details.
So far Tubos de plástico de soldadura has created 170 blog entries.

Fusion, through Butt welding operation, the 8 most usual mistakes.

Fusion through Butt welding operation in polyethylene high density pipes (HDPE) it is based on a union throughout two surfaces, which are heated due to the application of a specific heat temperature, from that point a precise pressure it is implemented till both surfaces finally get fused. The heat changes the plastic molecular structure, from the crystalline state to a shapeless state, so when the pressure it is performed produces the mixture of these molecules. With the cooling, the molecules [...]

By |2019-05-23T11:42:13+00:00May 22nd, 2019|Uncategorized|0 Comments

Socket welding, the fusion by plug the plastic pipes each other.

The Socket welding process, which is known as poly-fusion, snap-in welding and embossing fusion too,  consists in using a kind of  female/male welding matrices, which gets heated at the same time, in the inside and the outside part of the fitting , the inside and the outside part and the pipe, so when they are hot they could be joined using the pressure. In other words, the socket welding it is performed by snapping in the inside pipe the fitting, [...]

By |2019-05-23T11:43:13+00:00May 22nd, 2019|Uncategorized|0 Comments

Real solutions for the 5 trillion pieces plastics that currently littler our oceans

   There are currently over 5 trillion pieces of plastic our oceans. Ocean currents gather plastic trash basically in 5 main patches around our oceans, largest one between Hawaii and California, at the Great Pacific Garbage Patch.   This is an actual serious environmental problem, which is starting to affect our ecosystems, our own health and economies. If we don’t do anything, situation can get even worst. Solving the problem will require closing the source and cleaning up what is [...]

By |2018-11-02T12:01:50+00:00July 16th, 2018|Uncategorized|0 Comments

Want to triplicate Your Daily Welding Output?

Last post, we discussed various fusion standards and how the ISO High Force standard in particular — an option that is achievable with McElroy equipment — can produce twice as many fusion welds per day with less cooling time required. Today, we would like to highlight the McElroy machine features that make the large-diameter pipe fusion process even more productive. These special features allow us to produce three times as many fusion welds a day as other machines using the ISO [...]

By |2019-04-25T14:48:03+00:00June 7th, 2018|Uncategorized|1 Comment

Want to Double Your Daily Welding Output?

If you wish to double your daily welding, we will explain how. With this machine we can weld the double welding of 250mm pipe lines daily. Over the years as HDPE has been installed in pipelines worldwide there have been numerous welding standards created, almost one for each country, for example UNE, UNI, DVS, WIS, ANSI, ASTM. The ISO standards were created in an effort to harmonize the various standards and create one set that would encompass the best procedures and [...]

By |2018-11-02T12:01:51+00:00May 31st, 2018|Uncategorized|0 Comments

AQUACULTURE, FISH FARMS AND MARINE FARMS WITH PE PIPES

Aquaculture is the farming of fish, molluscs, crustaceans and algae in “more or less controlled” conditions. It constitutes one of the few industrial activities developed by the man who is integrated in the environment from the higher and most exquisite of respects helping, not in only few occasions, to its regeneration. This “young” activity started to be developed in the environment which is better dominated by the man: the LAND. But with the pass of time, the logical tendency has been [...]

By |2018-11-02T12:01:51+00:00May 24th, 2018|Uncategorized|0 Comments

Break pressure manholes and calculation of the pump unit power

  • Break pressure manholes In some installations with a steep and long slope in which water goes down from a deposit, spring, etc. it is necessary to break the growing pressure which is produced in the parte inferior of the pipe with the aim of not having excessive pressure in the case that the pipe transfers the load or suffers some obstruction. […]

How electrofusion pipes and PE fittings are performed

Normal 0 21 false false false ES X-NONE X-NONE MicrosoftInternetExplorer4 st1:*{behavior:url(#ieooui) } /* Style Definitions */table.MsoNormalTable{mso-style-name:”Tabla normal”;mso-tstyle-rowband-size:0;mso-tstyle-colband-size:0;mso-style-noshow:yes;mso-style-priority:99;mso-style-qformat:yes;mso-style-parent:””;mso-padding-alt:0cm 5.4pt 0cm 5.4pt;mso-para-margin:0cm;mso-para-margin-bottom:.0001pt;mso-pagination:widow-orphan;font-size:10.0pt;font-family:”Calibri”,”sans-serif”;}When a low tension electric current (from 8 to 48 V) is passed through the metal coils of electrowelding fittings, heating is produced (Joule Effect) that welds the pipe to the fitting. […]

Do you know Trenchless Technologies (no-dig) with plastic pipes?

1) DRIVEN DRILLING. At present it is being used horizontal driven drilling with PE pipes up to 1200 mm diameter and over. It is ideal to overcome obstacles and existing services.  It allows junctions at different depths always working in the surface. It is used for any type of service. […]

10 Remarkable advantages of Polyethylene (PE) pipes

Polyethylene extrusión in the prehistory Every time I see this vignette, I think, perhaps because of professional deformation,  which perfectly represents the fundamental parameters of PE pipe manufacturing, ie, pressure (clubbed), temperature (fire) and time (depending on the bone length). These parameters are the ones we have to control during the PE extrusion. […]